Tripp Lite Home Theater System Home Theater Surge Suppressors User Manual

Home Theater  
Surge Suppressors  
Owner’s Manual  
IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.  
CAUTION! DO NOT connect to an ungrounded outlet. DO NOT use with 2-wire extension cords or adapters. This surge suppressor  
is designed for indoor use only. Install the surge suppressor away from heat-emitting appliances such as radiators or heat registers.  
Do not install where excessive moisture is present. Do not plug extension cords into it. Never install electrical, telephone, network  
or coaxial wiring during a lightning storm. Do not drill into any part of the housing or open the housing for any reason. There are  
no user-serviceable parts inside.  
Select models feature an internal protection that  
Connect Your Equipment to the Surge Suppressor’s Coaxial Jacks  
will disconnect the surge-protective component at the  
end of its useful life but will maintain power to the load—  
now unprotected.  
(Optional Installation): Connect a coaxial cable from the wall jack directly to  
the surge suppressor’s “F” style coaxial jack labeled “IN.” Connect a coaxial  
cable from the surge suppressor’s “F” style coaxial jack labeled “OUT” directly to  
the device to be connected. Select models include a second set of coaxial jacks  
for simultaneous connection and protection of devices on two separate lines (cable,  
antenna or satellite). The surge suppressor must always be the first item con-  
nected in line from the coaxial wall jack. The surge suppressor must be plugged into  
a 3-wire grounded AC outlet for coaxial line surge protection to work. Make  
sure coax cables connected to satellite dishes, antennas, etc. are also grounded.  
Installation  
Mount Your Surge Suppressor (Optional Installation): If desired, mount  
your surge suppressor on a wall or other sturdy, vertical surface. However, you  
must mount the surge suppressor prior to connecting your equipment. Place a  
sheet of paper over the surge suppressor’s mounting holes and mark their cen-  
ters with a push pin. Next, place this template over the desired area and mark  
with the push pins. Install screws (user supplied) into the marks until ¼ in. (0.5  
cm.) of the screw heads are exposed. Mount the surge suppressor over the  
screw heads and slide into place.  
FCC Part 68 Notice (United States Only)  
If your Modem/Fax Protection causes harm to the telephone network, the telephone company may temporarily discontinue your  
service. If possible, they will notify you in advance. If advance notice isn’t practical, you will be notified as soon as possible. You  
will be advised of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment,  
operations or procedures that could affect the proper operation of your equipment. If it does, you will be given advance notice to  
give you an opportunity to maintain uninterrupted service. If you experience trouble with this equipment’s Modem/Fax Protection,  
please contact Technical Support, Tripp Lite; 1111 W. 35th Street, Chicago, IL 60609; Phone: (773) 869-1234, for repair/warranty  
information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or  
you are sure the equipment is not malfunctioning. There are no repairs that can be made by the customer to the Modem/Fax  
Protection. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject  
to state tariffs. (Contact your state public utility commission or corporation commission for information.)  
Connect Your Surge Suppressor to the AC Power Line: Plug the surge  
suppressor’s power cord into a standard, 3-wire grounded 120V AC, 60 Hz. outlet.  
Turn Your Surge Suppressor ON: Press the surge suppressor’s power switch  
down or to “RESET” (depending on model). Select models feature an illumi-  
nated switch.  
Lifetime Limited Warranty  
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and  
workmanship for its lifetime. If the product should prove defective in material or workmanship within that period, Seller will repair or  
replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the product  
(with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th St., Chicago, IL 60609. Seller will pay return shipping charges.  
Check Your Surge Suppressor’s Diagnostic Indicator Lights: Check the  
LEDs prior to connecting your equipment. They will indicate various operating  
conditions when the surge suppressor is plugged into a live 120V AC outlet  
and the surge suppressor’s power switch is on.  
The warranties of all TRIPP LITE surge suppressors are null and void if they have been connected to the output of any UPS system.  
The warranties of all TRIPP LITE UPS Systems are null and void if a surge suppressor has been connected to its output receptacles.  
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE  
OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH  
HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WAR-  
RANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH  
ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTALAND CONSEQUENTIAL DAMAGES. (Some states  
do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental  
or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal  
rights, and you may have other rights which vary from jurisdiction to jurisdiction.)  
“PROTECTED” LED: Indicates the surge suppression components are  
intact and providing complete protection against surges. If this LED does not  
illuminate, some of the surge suppression components are not functioning,  
and the unit should be replaced. Call Tripp Lite Customer Support at (773)  
869-1234.  
“GROUNDED” LED: Indicates wall outlet is grounded and surge protection  
can properly function. If this light DOES NOT illuminate and power is pres-  
ent, consult a qualified electrician to examine your outlet’s wiring.  
TRIPP LITE; 1111 35th St.; Chicago, IL 60609  
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the  
use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty  
as to the suitability or fitness of these devices for any specific application.  
Connect Your Equipment to the Surge Suppressor’s AC Outlets: Plug  
your equipment’s power cords (including 2-wire devices) into the surge sup-  
pressor’s AC outlets. Select models feature integrated safety covers which cover the  
outlets when not in use. Other models feature special widely-spaced outlets to  
accommodate transformers without covering other outlets. DO NOT plug in  
extension cords. DO NOT OVERLOAD the surge suppressor’s outlets. The  
surge suppressor can accommodate a total equipment load of up to 15 amps  
(whether plugged into a single outlet or spread out over multiple outlets). If  
the load on the surge suppressor exceeds 15 amps, the circuit breaker* will trip  
and the outlets will stop providing power. If the circuit breaker trips, reduce the  
load by unplugging some devices. Depress the circuit breaker or switch to  
“RESET” to reset the breakers and restore power.  
Policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.  
Regulatory Compliance Identification Numbers  
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique  
series number. The series number can be found on the product nameplate label, along with all required approval markings and  
information. When requesting compliance information for this product, always refer to the series number. The series number  
should not be confused with the marking name or model number of the product.  
This product designed and engineered in the USA.  
Ultimate Lifetime Insurance Policy  
(Valid in the U.S. and Canada Only)  
Tripp Lite warrants, for the lifetime of the product, (at Tripp Lite's option) to repair or replace (on a pro rata basis) directly connected  
equipment that is damaged due to power transients while properly connected to Tripp Lite products offering the Ultimate Lifetime  
Insurance Policy. Power transients include spikes and surges on the AC power, data or telephone lines that the Tripp Lite products  
have been designed to protect against (as recognized by industry standards).  
* Circuit breakers are integrated into the power switch on select models and offered as a separate  
feature on other models.  
AC Power Line Transients: To claim damages, the Tripp Lite product must be plugged into a properly wired and grounded outlet. No  
extension cords or other electrical connections may be used. The installation must comply with all applicable electrical and safety  
codes set forth by the National Electrical Code (NEC). Except as provided above, this warranty does not cover any damage to prop-  
erly connected electronic equipment resulting from a cause other than an “AC power transient”. If user meets all of the above require-  
ments, Tripp Lite will repair or replace (at Tripp Lite’s option) equipment up to the specified value (See Ultimate Lifetime Insurance  
Policy Limits). No coverage is allowed for damage entering from telephone or data lines, unless they are separately protected, as  
described below.  
Connect Your Equipment to the Surge Suppressor’s Phone Jacks  
(Optional Installation. Available on Select Models Only): Connect a phone  
cable from the wall jack directly to the surge suppressor’s RJ-style phone jack  
labeled “IN.” Connect a phone cable from the surge suppressor’s RJ-style phone  
jack labeled “OUT” directly to the device to be protected. Select models feature  
two “OUT” jacks; either one or both of the jacks may be used, but protection  
is for a device or devices sharing a single line only. The surge suppressor must  
always be the first item connected in line from the wall jack. The surge suppres-  
sor must be plugged into a 3-wire, grounded AC outlet for phone line surge pro-  
tection to work.  
Telephone and Data Line Transients: Tripp Lite will repair or replace directly connected equipment that is damaged by transients on  
telephone and/or data lines only when all such paths are protected by a Tripp Lite protection product(s) and the AC power (utility) line  
is simultaneously protected by a Tripp Lite power protection device (UPS, surge suppressor or line conditioner) with Ultimate Lifetime  
Insurance coverage. Additional telephone and/or data line connected devices downstream must have their own telephone and/or  
dataline protectors.  
Reimbursement dollar limits will be equal to that of the Tripp Lite power protection protector. Coverage is excluded where a suitable  
environment for the protection device is not provided, including, but not limited to, lack of a proper safety ground. Telephone service  
equipment must also include a properly installed and operating "primary protection" device at the telephone service entrance (such  
devices are normally added during telephone line installation).  
All above warranties are null and void if the Tripp Lite product has been improperly installed, tampered with or altered in any way, or  
if the connected equipment was not used under normal operating conditions or in accordance with any labels or instructions. All claims  
under this warranty must be submitted in writing to Tripp Lite within 30 days of the occurrence or the claim will not be considered.  
This warranty does not include damage resulting from accident or misuse, and applies to the domestic (USA & Canada) use of these  
products only.  
Connect Your Equipment to the Surge Suppressor’s Network Jacks*  
(Optional Installation. Available on Select Models Only): Connect a data  
cord from the wall jack or cable/DSL modem directly to the surge suppressor’s  
network jack labeled “IN.” Connect a data cord from the surge suppressor’s  
network jack labeled “OUT” directly to the device to be protected. The surge  
suppressor must always be the first item connected in line from the Ethernet  
source (typically a wall jack). The surge suppressor must be plugged into a  
3-wire grounded AC outlet for network line surge protection to work.  
* 10/100 BaseT/TX, Token Ring. Not compatible with PoE (Power Over Ethernet) applications.  
Tripp Lite reserves the right to determine whether the damage to the connected equipment is due to malfunction of the Tripp Lite product  
by requesting the equipment in question be sent to Tripp Lite for examination. This policy is above and beyond, only to the extent  
needed, of that provided by any coverage of connected equipment provided by other sources, including, but not limited to, any man-  
ufacturer’s warranty and/or any extended warranties.  
EXCEPT AS PROVIDED ABOVE, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES  
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of  
implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to purchaser.  
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL  
OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY  
OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use  
of equipment, loss of software, loss of data, costs of substitutes, claims by third parties or otherwise. Coverage also does not apply  
to connected medical and industrial equipment.  
To receive service under this warranty, you must be the original purchaser/user of the product in question. You must obtain a Returned  
Material Authorization (RMA) number from Tripp Lite. Products must be returned to Tripp Lite with transportation charges prepaid and  
must be accompanied by a brief description of the problem encountered and proof of date and place of purchase.  
Copyright © 2005. All rights reserved.  
 

Taylor Scale 7356 User Manual
Techno Source Video Games 21500 User Manual
TOA Electronics Car Amplifier VM 2120 User Manual
Toshiba Thermometer HT 201 User Manual
Tripp Lite Power Supply SUPDM12 User Manual
Tripp Lite Switch P772 002 User Manual
Ultra Start Automobile Alarm 22xx User Manual
Uniflame Indoor Fireplace EF700SP User Manual
Wacom Whiteboard Accessories DTU 710 User Manual
Weber Charcoal Grill PERFORMER PLATINUM User Manual